forked from wireshark/wireshark
-
Notifications
You must be signed in to change notification settings - Fork 0
/
NEWS
146 lines (102 loc) · 5.45 KB
/
NEWS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
Wireshark 3.3.2 Release Notes
This is an experimental release intended to test new features for
Wireshark 3.4.
What is Wireshark?
Wireshark is the world’s most popular network protocol analyzer. It is
used for troubleshooting, analysis, development and education.
What’s New
Many improvements have been made. See the “New and Updated Features”
section below for more details.
New and Updated Features
The following features are new (or have been significantly updated)
since version 3.3.1:
• Nothing of note.
The following features are new (or have been significantly updated)
since version 3.3.0:
• The Windows installers now ship with Npcap 1.00. They previously
shipped with Npcap 0.9997.
• The Windows installers now ship with Qt 5.15.1. They previously
shipped with Qt 5.12.8.
The following features are new (or have been significantly updated)
since version 3.2.0:
• Windows executables and installers are now signed using SHA-2
only[1].
• Save RTP stream to .au supports any codec with 8000 Hz rate
supported by Wireshark (shown in RTP player). If save of audio is
not possible (unsupported codec or rate), silence of same length
is saved and warning is shown.
• Asynchronous DNS resolution is always enabled. As a result, the
c-ares library is now a required dependency.
• Protobuf fields can be dissected as Wireshark (header) fields
that allows user input the full names of Protobuf fields or
messages in Filter toolbar for searching.
• Dissectors based on Protobuf can register themselves to a new
'protobuf_field' dissector table, which is keyed with the full
names of fields, for further parsing fields of BYTES or STRING
type.
• Wireshark is able to decode, play, and save iLBC payload on
platforms where the iLBC library[2] is available.
• Wireshark is able to decode, play, and save opus payload on
platforms where the opus library[3] is available.
• “Decode As” entries can now be copied from other profiles using a
button in the dialog.
• sshdump can now be copied to multiple instances. Each instance
will show up a different interface and will have its own profile.
• The main window now supports a packet diagram view, which shows
each packet as a textbook-style diagram.
• Filter buttons (“Preferences → Filter Buttons”) can be grouped by
using “//” as a path separator in the filter button label.
New Protocol Support
Arinc 615A (A615A), Asphodel Protocol, AudioCodes Debug Recording
(ACDR), Bluetooth HCI ISO (BT HCI ISO), Cisco MisCabling Protocol
(MCP), Community ID Flow Hashing (CommunityID), DCE/RPC
IRemoteWinspool SubSystem, (IREMOTEWINSPOOL), Dynamic Link Exchange
Protocol (DLEP), EAP Generalized Pre-Shared Key (EAP-GPSK), EAP
Password Authenticated Exchange (EAP-PAX), EAP Pre-Shared Key
(EAP-PSK), EAP Shared-secret Authentication and Key Establishment
(EAP-SAKE), Fortinet Single Sign-on (FSSO), FTDI Multi-Protocol
Synchronous Serial Engine (FTDI MPSSE), Hypertext Transfer Protocol
Version 3 (HTTP3), ILDA Digital Network (IDN), ILDA Digital Network
(IDN), Java Debug Wire Protocol (JDWP), LBM Stateful Resolution
Service (LBMSRS), Lithionics Battery Management, OBSAI UDP-based
Communication Protocol (UDPCP), Palo Alto Heartbeat Backup
(PA-HB-Bak), ScyllaDB RPC, Technically Enhanced Capture Module
Protocol (TECMP), Tunnel Extensible Authentication Protocol (TEAP),
UDP based FTP w/ multicast V5 (UFTP5), and USB Printer (USBPRINTER)
Updated Protocol Support
Too many protocols have been updated to list here.
New and Updated Capture File Support
MP4 (ISO/IEC 14496-12)
Getting Wireshark
Wireshark source code and installation packages are available from
https://www.wireshark.org/download.html.
Vendor-supplied Packages
Most Linux and Unix vendors supply their own Wireshark packages. You
can usually install or upgrade Wireshark using the package management
system specific to that platform. A list of third-party packages can
be found on the download page[4] on the Wireshark web site.
File Locations
Wireshark and TShark look in several different locations for
preference files, plugins, SNMP MIBS, and RADIUS dictionaries. These
locations vary from platform to platform. You can use About → Folders
to find the default locations on your system.
Getting Help
The User’s Guide, manual pages and various other documentation can be
found at https://www.wireshark.org/docs/
Community support is available on Wireshark’sQ&A site[5] and on the
wireshark-users mailing list. Subscription information and archives
for all of Wireshark’s mailing lists can be found on the web site[6].
Bugs and feature requests can be reported on the issue tracker[7].
Frequently Asked Questions
A complete FAQ is available on the Wireshark web site[8].
Last updated 2020-10-11 09:04:20 UTC
References
1. https://support.microsoft.com/en-us/help/4472027/2019-sha-2-code-s
igning-support-requirement-for-windows-and-wsus
2. https://github.com/TimothyGu/libilbc
3. https://opus-codec.org/
4. https://www.wireshark.org/download.html#thirdparty
5. https://ask.wireshark.org/
6. https://www.wireshark.org/lists/
7. https://gitlab.com/wireshark/wireshark/-/issues
8. https://www.wireshark.org/faq.html