-
Notifications
You must be signed in to change notification settings - Fork 11
Torlus/FPGAPCE
This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository.
Folders and files
Name | Name | Last commit message | Last commit date | |
---|---|---|---|---|
Repository files navigation
================================================================================ fpgapce - a NEC PC-Engine/Turbografx-16 clone in a FPGA. Copyright (c) 2011-2013 Gregory Estrade ([email protected]) All rights reserved fpgapce is an attempt to clone the NEC PC-Engine/Turbografx-16 console in a FPGA. It is currently advanced enough to run many games. ================================================================================ In order to run this project you will need : - A Terasic/Altera DE1 board. - A VGA monitor. - A headset, if you want to enjoy sound. - DE1 CD-ROM contents. (http://www.terasic.com/downloads/cd-rom/de1/) - Altera Quartus II 9.1 Web Edition. - (optional) ModelSim-Altera 6.5b Starter Edition. First, the FPGA EEPROM should be programmed with the demonstration design "DE1_USB_API.sof". It should be the case if you've never re-programmed it. That will allow you to use the "DE1 Control Panel" software. Power on your DE1 board, make it sure it is connected thru USB to your computer. Run the "DE1_Control_Panel.exe" program. Click on "Open", select "Open USB Port 0". Select the "FLASH" tab, and click on "Chip Erase". Check "File Length", then click on "Write a File to FLASH". Choose a PC-Engine ROM. Once the write operation is done, close the "DE1 Control Panel". If you downloaded the programming file, run the Quartus Programmer ("quartus_pgmw.exe" located in "<altera root directory>\91\quartus\bin"). Select the "pce_top.sof" file, click on "Start", and you're done! Notes : - Be sure to always perform a "Chip Erase" before programming a new ROM. - I don't know if it's due to my own setup, but I've found that the flash write operation is not very reliable, as I often get a byte off when I try to read back the flash. For some games it doesn't matter (if you're lucky enough, and that the write error occurs in a data section, and not a code section). Some games however perform a self-consistency check, and won't run at all. Only workaround so far : erase and re-program the flash until it succeeds. ROMs are cartridge memory dumps, that may include a 512-bytes header. There is also a special memory mapping for ROMs that have a size of 768 Kb. So I've set up some switches to cope with these different configurations : - SW1 : header present or not (usually, ROMs do have this header, so set it to "1"). - SW2 : set it to "1" if your ROM is 768 Kb. - SW3 : set it to "1" if you're dealing with a TGFX ROM instead of a PCE ROM. NEC created a very basic region-lockout by swapping data bits on the cartridge and cartridge connector on US (TGFX-16) consoles. So, for the (very few) ROMs that have been dumped off a US cartridge, set it to "1". If unsure, set it to "0". A 4-button pad is mapped to the board's switches and buttons. Here is a description of the controls : - KEY0 : Button I - KEY1 : Button II - KEY2 : Run - KEY3 : Select - SW9 : Up - SW8 : Down - SW7 : Left - SW6 : Right SW0 performs a Hard-Reset operation. ================================================================================ Gregory Estrade (Torlus) - 2012/02/02 [email protected]
About
PC-Engine / Turbografx-16 clone running on an Altera DE1 board.
Resources
Stars
Watchers
Forks
Releases
No releases published
Packages 0
No packages published