Skip to content

mean00/stm32ComponentTester

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

STM32 Component tester

screenshot NB: This prototype is done using a discrete chip, you can also use a bluepill board.

Scope

This project is a redone from scratch component tester ( see https://www.mikrocontroller.net/articles/AVR-Transistortester ).

The tester is powered by a STM32F103/GD32F103 or GD32F303 MCU. You can also use directly a bluepill board.

The shopping list is (when using a bluepill board)

  • Bluepill board
  • 1.44' SPI 128x128 screen ( Ebay Link)
  • LMV324i Quad op Amp (or any rail to rail quad op amp)
  • Rotary Encoder
  • AMS 3.3v voltage regulator regulator or similar
  • (470 Ohms, 15kOhm, 470kOhm) x3

If you want to use the MCU directly, look at kicad/schematic.pdf Due to the low voltage (3.3v), some mosfet will not be tested correctly.

Features

  • Resistor
  • Capacitors (from ~ 2 pf to ~ 600 uF)
  • NPN and PNP transistors : Hfe, Base-Emitter forward diode voltage
  • N & P Mosfet : GS capacitance, RDSon, diode voltage, VgsOn

How to build

  • Install arduino and cmake
  • Checkout the project, make sure you checkout the submodules i.. git clone --recurse-submodules http://xxxxx
  • Edit platformConfig.cmake to set the path to your compiler (i strongly suggest to use that ( one) )
  • mkdir build && cd build && cmake .. && make

/!\ Important : On mingw dont forget to do dos2unix patches/*.diff

It should work fine on linux and windows/mingw.

Options

By default the firmware is generated for STM32F103C8T6 For the GD32F103 : add -DUSE_GD32F103=True to the cmake command For the GD32F303 : add -DUSE_GD32F303=True to the cmake command

/!\ Important : The code is very close to 64kB, + we need a bit of flash to store settings. As a result, it might not fit inside the GD32F1 or a STM32F1 with really 64 kB of flash.

How does it work ?

The code is in two parts :

  • Identifying the component
  • Probing the component, using only the MCU ADC in single or dual mode.
  • For mosfets, since we dont have a DAC on the bluepill, we'll use the charge/discharge of the parasitic FET capacitor to act as a sort of DAC

Restriction

While accuracy is not bad at all the following restrictions apply :

  • Mosfet with VGsOn> 3.3 v will not be probed correctly
  • Inductors are disabled, not working properly
  • Capacitor of less than 4 pF will not be probed correctly
  • Capacitor can be reverse charged with a small current. I'm unsure if that's a big deal. The current is a few mA.

screenshot

About

No description, website, or topics provided.

Resources

License

Unknown, Unknown licenses found

Licenses found

Unknown
LICENSE
Unknown
License.txt

Stars

Watchers

Forks

Packages

No packages published