Voron 2.4 (300mm³)

• Voron 2.4 (300mm³)
• Installed Upgrades
• Filament Management
• Update Klipper
  • Automatic update script
  • Manual settings
    • RPi
    • Spider
    • BTT MMU (CAN)
    • BTT EBB SB2240 (CAN)

Installed Upgrades

• Nevermore Micro V5 Duo (dual fan)
• Bearing stacks instead of toothed idlers
• Single MGN12
• Klicky
• ERCF
• Extrusion Backers (only on Y)
• Voron Tap
• Beefy Front Idlers
• GE5C Slim

Filament Management

Print labels for spool and filament test card

 $ labelle --qr "web+spoolman:s-XXX" "SUNLU" "ABS" "Black"

Map gates in MMU to spool

MMU_GATE_MAP GATE=2 MATERIAL=ABS+ COLOR=FFFF00 SPOOLID=2

Update Klipper

Automatic update script

$ ~/klipper_config/script/update_mcu.sh

Manual settings

$ cd ~/klipper
$ make menuconfig

RPi

[*] Enable extra low-level configuration options
    Micro-controller Architecture (Linux process)  --->
()  GPIO pins to set at micro-controller startup

$ make clean && make
$ sudo service klipper stop
$ make flash
$ sudo service klipper start

Fysetc Spider

https://github.com/FYSETC/FYSETC-SPIDER

[*] Enable extra low-level configuration options
    Micro-controller Architecture (STMicroelectronics STM32)  --->
    Processor model (STM32F446)  --->
    Bootloader offset (64KiB bootloader)  --->
    Clock Reference (12 MHz crystal)  --->
    Communication interface (Serial (on USART1 PA10/PA9))  --->
(250000) Baud rate for serial port
()  GPIO pins to set at micro-controller startup

$ make clean && make
$ sudo service klipper stop
$ ./scripts/flash-sdcard.sh /dev/ttyAMA0 fysetc-spider-v1
$ sudo service klipper start

BTT MMB (CAN)

https://github.com/bigtreetech/MMB

Katapult

    Micro-controller Architecture (STMicroelectronics STM32) --->
    Processor model (STM32G0B1) --->
    Build CanBoot deployment application (Do not build) --->
    Clock Reference (8 MHz crystal)  --->
    Communication interface (CAN bus (on PB0/PB1)) --->
    Application start offset (8KiB offset)  --->
(1000000) CAN bus speed
()  GPIO pins to set at micro-controller startup
[*] Support bootloader entry on rapid double click of reset button
[ ] Enable bootloader entry on button (or gpio) state
[ ] Enable Status LED

Klipper

[*] Enable extra low-level configuration optionsMicro-controller
    Micro-controller Architecture (STMicroelectronics STM32) --->
    Processor model (STM32G0B1) --->
    Bootloader offset (8KiB bootloader) --->
    Clock Reference (8 MHz crystal)  --->
    Communication interface (CAN bus (on PB0/PB1)) --->
(1000000) CAN bus speed
()  GPIO pins to set at micro-controller startup

$ python3 ~/katapult/scripts/flashtool.py -i can0 -u 13d7b8824ae8 -f ~/klipper/out/klipper.bin

BTT EBB SB2240 (CAN)

https://github.com/bigtreetech/EBB/tree/master/EBB%20SB2240_2209%20CAN

Katapult

    Micro-controller Architecture (STMicroelectronics STM32) --->
    Processor model (STM32G0B1) --->
    Build CanBoot deployment application (8KiB bootloader) --->
    Clock Reference (8 MHz crystal)  --->
    Communication interface (CAN bus (on PB0/PB1)) --->
    Application start offset (8KiB offset)  --->
(1000000) CAN bus speed
()  GPIO pins to set at micro-controller startup
[*] Support bootloader entry on rapid double click of reset button
[ ] Enable bootloader entry on button (or gpio) state
[*] Enable Status LED
(PA13)  Status LED GPIO Pin

Klipper

[*] Enable extra low-level configuration optionsMicro-controller
    Micro-controller Architecture (STMicroelectronics STM32) --->
    Processor model (STM32G0B1) --->
    Bootloader offset (8KiB bootloader) --->
    Clock Reference (8 MHz crystal)  --->
    Communication interface (CAN bus (on PB0/PB1)) --->
(1000000) CAN bus speed
()  GPIO pins to set at micro-controller startup

python3 ~/katapult/scripts/flashtool.py -i can0 -u f7ad7cd429e2 -f ~/klipper/out/klipper.bin