My configs and macros for 2in1out Phateus Taichi hotend DD configuration with 2x Sailfin extruder
Prusa slicer settings Disable pressure_advance insert from Prusa slicer
Taichi parameters
Start print G code (for Prusaslicer, not Klipper!!!!)
G90 ; use absolute coordinates M83 ; extruder relative mode M104 S150 ; set temporary nozzle temp to prevent oozing during homing M140 S{first_layer_bed_temperature[0]} ; set final bed temp G4 S30 ; allow partial nozzle warmup G28 ; home all axis G29 ;if you need to level bed each print, comment out if not BED_MESH_PROFILE LOAD=p1
G1 Z50 F240 G1 X2.0 Y12 F3000 M104 S{first_layer_temperature[0]} ; set final nozzle temp M190 S{first_layer_bed_temperature[0]} ; wait for bed temp to stabilize M109 S{first_layer_temperature[0]} ; wait for nozzle temp to stabilize ;T0 ;T1 LOAD_FILAMENT G1 Y30 Z0.28 F240 G92 E0 G1 X2.0 Y155 E10 F1500 ; prime the nozzle G1 X2.3 Y140 F5000 G92 E0 G1 X2.3 Y30 E10 F1200 ; prime the nozzle G1 Z4 F240 G92 E0
#NOTE! #####################################################################
;T0 ;T1 Will activate and with single or both extruders (starting extruder T0) depending if object is single or two materials
;T0 T1 Will activate and with single or both extruders (starting extruder T1) depending if object is single or two materials and if material to use is already loaded in T1 extruder and you don't feel like swapping it to T0 extruder :D.
[delayed_gcode activate_default_extruder] initial_duration: 1 gcode: ACTIVATE_EXTRUDER EXTRUDER=extruder
[gcode_macro T0] gcode:
SYNC_STEPPER_TO_EXTRUDER STEPPER=extruder1 EXTRUDER=
SYNC_STEPPER_TO_EXTRUDER STEPPER=extruder EXTRUDER=extruder
[gcode_macro T1] gcode:
SYNC_STEPPER_TO_EXTRUDER STEPPER=extruder EXTRUDER=
SYNC_STEPPER_TO_EXTRUDER STEPPER=extruder1 EXTRUDER=extruder
[gcode_macro ACTIVATE_EXTRUDER] description: Replaces built-in macro for a X-in, 1-out extruder configuration SuperSlicer fix rename_existing: ACTIVATE_EXTRUDER_BASE gcode: {% if 'EXTRUDER' in params %} {% set ext = params.EXTRUDER|default(EXTRUDER) %} {% if ext == "extruder"%} {action_respond_info("Switching to extruder0.")} T0 {% elif ext == "extruder1" %} {action_respond_info("Switching to extruder1.")} T1 {% else %} {action_respond_info("EXTRUDER value being passed.")} ACTIVATE_EXTRUDER_BASE EXTRUDER={ext} {% endif %} {% endif %}
#Phateus Taichi #Those two macros are called from Klipperscreen-> Extrude-> Load/ Unload filament
[gcode_macro LOAD_FILAMENT] #description: This will move filament to the nozzle assuming parked position (TaiChi hotend) gcode: M83 G1 E8.6000 F120 G1 E30.1000 F207 G1 E4.3000 F145 #G1 E60 F145 M82
[gcode_macro UNLOAD_FILAMENT] #description: This will form tip and move filament to parked position assuming filament is at nozzle (TaiChi hotend) gcode: M83 G1 E20.0000 F300 G1 E-15.0000 F1500 G1 E-9.8000 F2400 G1 E-2.8000 F1200 G1 E-1.4000 F720
G1 E5.0000 F3000 G1 E-5.0000 F2780 G1 E5.0000 F3000 G1 E-5.0000 F2750 G1 E5.0000 F3000 G1 E-5.0000 F2700 G1 E5.0000 F3000 G1 E-5.0000 F262 G1 E-16.000 F200 M82
#KIAUH and other macros
[delayed_gcode bed_mesh_init] initial_duration: .01 gcode: BED_MESH_PROFILE LOAD=p1
[gcode_macro G29] gcode: #G1 E-1 F500 G28 BED_MESH_CALIBRATE BED_MESH_PROFILE SAVE=p1 #BED_MESH_PROFILE LOAD=p1 G1 X20 Y70 Z10 F4000 @BEDLEVELVISUALIZER BED_MESH_OUTPUT
[gcode_macro PID_TUNE_EXTRUDER] gcode: PID_CALIBRATE HEATER=extruder TARGET=210 WRITE_FILE=1
[gcode_macro PID_TUNE_BED] gcode: PID_CALIBRATE HEATER=heater_bed TARGET=60 WRITE_FILE=1
[gcode_macro Resonance_compensation] gcode: SET_VELOCITY_LIMIT ACCEL_TO_DECEL=7000 SET_PRESSURE_ADVANCE ADVANCE=0 SET_INPUT_SHAPER SHAPER_FREQ_X=0 SHAPER_FREQ_Y=0 TUNING_TOWER COMMAND=SET_VELOCITY_LIMIT PARAMETER=ACCEL START=1500 STEP_DELTA=500 STEP_HEIGHT=5
[gcode_macro Pressure_advance] gcode: SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=1 ACCEL=500 TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START=0 FACTOR=.002
[pause_resume]
[display_status]
[gcode_macro CANCEL_PRINT] rename_existing: BASE_CANCEL_PRINT gcode: G1 X0 Y220 F900 TURN_OFF_HEATERS CLEAR_PAUSE M84 M107 SDCARD_RESET_FILE BASE_CANCEL_PRINT
[gcode_macro PAUSE] rename_existing: BASE_PAUSE
variable_extrude: 1.0 gcode:
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
{% set x_park = printer.toolhead.axis_maximum.x|float - 25.0 %} {% set y_park = printer.toolhead.axis_maximum.y|float - 25.0 %}
{% set max_z = printer.toolhead.axis_maximum.z|float %} {% set act_z = printer.toolhead.position.z|float %} {% if act_z < (max_z - 10.0) %} {% set z_safe = 10.0 %} {% else %} {% set z_safe = max_z - act_z %} {% endif %}
SAVE_GCODE_STATE NAME=PAUSE_state BASE_PAUSE G91 G1 E-{E} F2100 G1 Z{z_safe} F900 G90 G1 X{x_park} Y{y_park} F6000 #G1 E15 F200
[gcode_macro RESUME] rename_existing: BASE_RESUME gcode:
{% set E = printer["gcode_macro PAUSE"].extrude|float %}
G91 G1 E{E} F2100 RESTORE_GCODE_STATE NAME=PAUSE_state BASE_RESUME
[gcode_macro idle_timeout] gcode: timeout: 36000
[gcode_macro BL_Touch_reset] gcode: BLTOUCH_DEBUG COMMAND=reset timeout: 5 BLTOUCH_DEBUG COMMAND=pin_down timeout: 5 BLTOUCH_DEBUG COMMAND=pin_up
[force_move] #enable_force_move: True
######################################################################################### #########################################################################################
#Printer.cfg
######## Note, I am using EBB CAN42. Second extruder driver is on Manta 5P ############################
[extruder] #EBB CAN 42 step_pin: EBBCan: PD0 dir_pin: EBBCan: PD1 enable_pin: !EBBCan: PD2 microsteps: 16 rotation_distance: 4.653 nozzle_diameter: 0.400 filament_diameter: 1.750 heater_pin: EBBCan: PB13 sensor_type: EPCOS 100K B57560G104F sensor_pin: EBBCan: PA3 #control: pid #pid_Kp: 21.527 #pid_Ki: 1.063 #pid_Kd: 108.982 min_temp: 0 max_temp: 270 pressure_advance: 0.05 min_extrude_temp: 180 max_extrude_only_distance: 700.0 max_extrude_cross_section: 50.0
[tmc2209 extruder] uart_pin: EBBCan: PA15 run_current: 0.850 stealthchop_threshold: 999999
[extruder_stepper extruder1] # Manta5P extruder: extruder step_pin: PB0 dir_pin: !PB1 enable_pin: !PC4 microsteps: 16 rotation_distance: 4.653 pressure_advance: 0.05
[tmc2209 extruder_stepper extruder1] uart_pin: PA6 run_current: 0.850 #diag_pin: