The board schematics, images at the time of this commit is found at
https://github.com/WeActTC/MiniSTM32H7xx

This variant is 'unofficial' (i.e. this is community contributed and not
from the original vendor)

it is actually adapted from the generic variant found in
https://github.com/stm32duino/Arduino_Core_STM32/tree/main/variants/STM32H7xx/H742V(G-I)(H-T)_H743V(G-I)(H-T)_H750VBT_H753VI(H-T)

the changes are:
1) created a void SystemClock_Config(void) that use the external 25 Mhz
HSE crystal. this makes it run at 480 Mhz ! USB (CDC Serial) still
works per normal.

much of the rest of the peripherals are clocked at 80 Mhz (from the
outputs of PLL2 and PLL3), that's the max allowable documented in ref
manual for the ADC.

2) the rest of definitions are pretty much same as the generic variant
with the following redefinitions
  a.  #define LED_BUILTIN PE3 (per schematics and tested)
  b.  #define USER_BTN PC13 (per schematics and tested)
  c.  SERIAL_TX PA9, SERIAL_RX PA10 - this makes the 1st hardware serial
      port UART1

3) added 2 conveinence functions - this is only for this board and is
only availaible if it is selected
   /* power saving mode, mcu runs significantly cooler
    * Sysclock 240 Mhz, bus clocks 120 Mhz */
  void SysClkHalfSpeed();

  /* full speed - sysclk from PLL1 P - 480 Mhz
   * Sysclock 480 Mhz, bus clocks 240 Mhz */
  void SysClkFullSpeed()

  This variant runs the systemclock default at 480 MHz (published max)
  and AHB at 240 MHz. The stm32h743 mcu tend to run pretty warm after a
  while (around 50 deg C). The half speed function call changes
  the system clock dividers (divide by 2 - gives 240 Mhz)
  and AHB dividers (divide further by 2 - gives 120 Mhz)
  so that it runs at 1/2 the PLL1 P speeds (480 Mhz).
  the mcu runs significantly cooler running at 1/2 speeds.
  some tests has been done to swtich the speeds calling the functions at
  run time, they seem to work ok. But tests isn't thorough, so check
  things if you use the speed changing functions.

change label WeActMiniH743VITX instead of WeActMiniH7xx

update variant_WeActMiniH743VITX.cpp add board ifdef to prevent other
boards from picking up definitions from this board (i.e. prevent cross
dependencies). This is to allow other similar boards to co-exist.

fix some astyle errors caused by spacing formatting (e.g. use space
instead of tabs)

update README.md entry for WeAct MiniSTM32H743VIT6 board

Signed-off-by: Frederic Pillon <[email protected]>

Signed-off-by: Frederic Pillon <[email protected]>

and add descriptions

Signed-off-by: Frederic Pillon <[email protected]>

Signed-off-by: Frederic Pillon <[email protected]>

Signed-off-by: Frederic Pillon <[email protected]>

Signed-off-by: Frederic Pillon <[email protected]>

several pins already connected to other peripherals

Signed-off-by: Frederic Pillon <[email protected]>

Signed-off-by: Frederic Pillon <[email protected]>

Signed-off-by: Frederic Pillon <[email protected]>

WeAct H7xx PR 1552